Automotive Electrical Tools

KIT-1706 New 6 Pc Diamond Sharpening Blocks This is a new 6 piece set of diamond coated sharpening blocks. These hard, sharp, tough, stones are available in various grits. Long recognized for the clean, sharp surfaces they produce on tools, dies, blades, molds and almost any other metal piece requiring sharpening or smoothing. You receive: * One blue coarse 150 grit block that measures approximately 6 1/16" x 2" * One blue coarse 150 grit block that measures approximately 3 9/16" x 1" * One red medium 300 grit block that measures approximately 6 1/16" x 2" * One red medium 300 grit block that measures approximately 3 9/16" x 1" * One yellow fine 400 grit block that measures approximately 6 1/16" x 2" * One yellow fine 400 grit block that measures approximately 3 9/16" x 1"

This sign is made of indoor/outdoor weatherproof.040 polystryrene (plastic as thick as 2 credit cards on top each other).This sign comes with rounded corners and one hole at each end for hanging.This is a great gift

20 piece precision ground twist drill set with storage case and pin vice. Great for electronics, crafts, jewelry, watch making. Includes the following sizes: #80 (.0135")#70 (.0280") #79 (.0145")#69 (.0292") #78 (.0160")#68 (.0310") #77 (.0180")#67 (.0320") #76 (.0200")#66 (.0330") #75 (.0210")#65 (.0350") #74 (.0225")#64 (.0360") #73 (.0240")#63 (.0370") #72 (.0250")#62 (.0380") #71 (.0260")#61 (.0390") Caution: Bits are sharp! You can easily stab yourself Always wear approved safety glasses These bits break easily. A fixture or vise is recommended No warranty for bit breakage These bits are so small they look very similar. Use a micrometer to verify size.

Professional Fluorescent Work Lights Type: Fluorescent Hand Lamp Lamp Included: Yes Type of Lamp: Fluorescent Cord Length: 25 Ft. Wire Type: SJT Wire Gauge/Conductors: 16/3 Wattage: 26

The DVI 1000HD extends DVI up to 1640 feet (500 meters) over fiber optics cables. The DVI 1000HDS sender unit sits next to your computer, set-top box or DVD player source. Cables supplied with the DVI 1000HD connect your DVI source to the send unit. The DVI 1000HDR receive unit sits next to your DVI display - up to 1640 feet (330 feet HDCP) away. The display plugs into the back of the DVI 1000HDR receiver unit. One CAT-5 cable and a multi mode LC fiber optic cable (4 strand) connect the DVI 1000HDS and the DVI 1000HDR units to each other.

The DVI-1000HD extends any DVI (digital visual interface) compliant device up to 1640 feet/500 meters (330 feet with HDCP) from the computer.PRODUCT FEATURES:Uses a four strand multimode LC-LC fiber optic cable;Uses one CAT-5 cable for DDC and control signals;Eliminates computer noise where you work;Supports resolutions up to 1080p, 2K, and 1920 x 1200;Supports DDWG standard for DVI compliant monitors;HDCP compliant.

Item #: PPRPP319CAMO. Features and BenefitsInstantly and safely power up, or ground, components with the press of the rocker switchBuilt in voltmeter reads DC voltage in 1/10 volt increments from 1v-70vdcPerform voltage drop test without having to grab your multimeter20 ft. cable allows you to power up and ground any circuit from bumper to bumper without the need for jumper leadsNew easy to read dual polarity indicators - A red (+) indicates positive and a green (-) indicates negative.The Limited Edition PPRPP319CAMO has all the benefits of the original Power Probe I and Power Probe II. You can power up and ground components, determine polarity instantly without having to flip flop your hook up clips, locate bad grounds, locate shorts, test for continuity, as well as activate relays and components from bumper to bumper without the use of jumper leads. All the features that have made the Power Probe a must for every technician and now with a built in voltmeter! The PPRPP319CAMO features a sleek new ergonomic design for better handling, a built in banana jack to ensure compatibility with our Gold Series Lead set, and a brand new Limited Edition Camouflage housing. Customers also search for: Tools and Storage\Automotive\Auto Electrical and Diagnostic Tools\Circuit Testers Discount Limited Edition Power Probe III Tester with Camouflage Housing, Buy Limited Edition Power Probe III Tester with Camouflage Housing, Wholesale Limited Edition Power Probe III Tester with Camouflage Housing, 878253000784, PP319CAMOCircuit Testers

The third release in the Power Probe line of diagnostic tools for auto electrical systems, the Power Probe III is the most revolutionary automotive circuit tester to date*. Packed with quick diagnostic power and multiple capabilities, this small, but powerful tool allows automotive technicians to literally speed through regularly scheduled maintenance and the troubleshooting of problems on automotive electrical systems, saving time and money. .caption { font-family: Verdana, Helvetica neue, Arial, serif; font-size: 10px; font-weight: bold; font-style: italic; } ul.indent { list-style: inside disc; text-indent: -15px; } table.callout { font-family: verdana; font-size: 11px; line-height: 1. 3em; } td.vgoverview { height: 125px; background: #9DC4D8 url(http://images.amazon.com/images/G/01/electronics/detail-page/callout-bg.png) repeat-x; border-left: 1px solid #999999; border-right: 1px solid #999999; padding-left: 20px; padding-right: 20px; padding-bottom: 10px; width: 250px; font-family: verdana; font-size: 12px; } How Does it Work? After connecting the Power Probe III's clips to the vehicle's battery, the automotive technician can determine at a glance, the voltage level and the polarity of a circuit without running for a volt meter or reconnecting hookup clips from one battery pole to the other. The power switch allows you to conduct a positive or negative battery current to the tip for activating and testing the function of electrical components without wasting time with jumper leads. And yes, the Power Probe III is short circuit protected. It tests for bad ground contacts instantly without performing voltage drop tests and locates short circuits without wasting precious fuses. It tests for continuity with the assistance of its auxiliary ground lead. Also, with a flip of the power switch, you will know instantly that your Power Probe III is functioning without running to the battery as you would otherwise have to do with simple test lights. Finally, the unit's 20-foot cable (extendable 40-feet) allows you to test along the entire length of the vehicle without constantly searching for ground hookups. Together, these features make the Power Probe III an absolute must for automotive technicians at all levels who are looking for a fast and accurate solution to electrical systems diagnostics. 5 powerful electrical auto diagnostic modes in 1 tool View larger. Powered by your car battery and including all the cable you'll need View larger. Five Modes in One Tool True to its design to provide auto technicians with a single tool for all their electrical systems diagnostic needs, the Power Probe III is packed with five powerful diagnostic modes. These include: Power Probe Mode, which indicates the average voltage level of the circuit; Negative Peak Mode, which monitors a positive circuit and captures the lowest voltage that it has dropped to; Positive Peak Mode, which monitors the probed circuit and captures the highest detected voltage; Peak to Peak Mode, which measures the difference between the positive and negative peak voltage levels over a 1 second period; and Threshold Level Setting Mode, used to adjust the threshold voltage in Power Probe Mode for peak to peak detection and signal monitoring. Standard Features: Built-in Flashlight. Audio tone test indicator. Volt meter and short circuit indicator. Relay and component tester and continuity tester. Bad ground indicator. Circuit breaker protected. Cable, with extension allowing for 40-feet of coverage Blow molded hard case for protection. What's in the Box Power Probe III handheld tool (with 20' cord), cigarette lighter adapter, 3" extension probe, battery hookup clips, 20 ft extension lead, instructional manual, blow molded case. Power Probe III Electrical Specifications: Minimum Voltage on Probe Tip: ± 200 volts relative to the negative battery clip Probe Tip Resistance to Ground: 130KΩ Power Probe Mode (Mode 1) DC voltage measurement: 0-70 volts AC voltage measurement: 0-70 volts Square wave input response: 15 Hz to over 500KHz Sine wave input response: 35 Hz to over 250KHz Continuity to ground: Greater than 20K Ohms - display is blank Less than 20K Ohms: Display reads 0.0 Less than 2K Ohms: Display reads 0.0 and green LED is on Min (Mode 2) & Max (Mode 3) Voltage measurement: 0-70 volts Single event capture: Less than 200 micro second pulse width Repetitive events: Less than 1 micro second pulse width Peak to Peak Mode (Mode 4) Voltage measurement: 0-70 volts Square wave input response: 4 Hz to over 500KHz Sine wave input response: 4 Hz to over 250KHz Peak to Peak Mode Threshold Setting (Mode 5) .2, .5, 1, 2, 5, 10, 50: When the Peak to Peak voltage exceeds this threshold then the display is Peak to Peak AC rather than DC Operating temperature: -20C to 55C Storage temperature: -40 C to 60C Circuit Breaker 8 amp thermal response - manual reset (8 amp=no trip, 10 amps=20 min., 15 amps=15 seconds, 25 amps=2 seconds, short circuit= 0.3 seconds *The Power Probe III is NOT to be used with 110/220-volt home electrical. It is only designed for use with 12-24 volt systems. About Power Probe, Inc. Headquartered in Brea, CA, Power Probe, Inc. has been a trusted manufacturer of motor vehicle supplies and tools for automotive technicians since 1994. Warranty Power Probe products undergo a strict quality control inspection for workmanship, function, and safety before leaving the factory. All Power Probe products carry a one-year limited warranty from the date of purchase, applicable to the original owner, to be free of defects in parts and workmanship.

Stanley 300 amp battery jumpstarter Jump start your battery without another car Built-in 120 Volt AC charger, recharges unit with standard household extension 270° Pivoting high powered LED emergency light Reverse connection warning provides audible and visual alarm 12 Volt and USB power outlets Enough power to start cars, small trucks, motorcycles and recreational vehicles with 12 volt battery systems Heavy duty metal clamps and cablesSTAJ309

Power Probe's Smart ECT2000 is an electronic circuit tracer that makes locating short and open circuits within a vehicle's wiring easier than ever before. Its advanced digital intelligence, built around a transmitter/receiver design, puts it far above all electronic tracers in the market, letting you quickly determine whether a circuit is shorted or open, regardless where it occurs in a vehicle. This coupled with built-in customization options and the array of adapters and clips included make it the easiest, fastest and most flexible way to trace circuits on your vehicles. .caption { font-family: Verdana, Helvetica neue, Arial, serif; font-size: 10px; font-weight: bold; font-style: italic; } ul.indent { list-style: inside disc; text-indent: -15px; } table.callout { font-family: verdana; font-size: 11px; line-height: 1. 3em; } td.vgoverview { height: 125px; background: #9DC4D8 url(http://images.amazon.com/images/G/01/electronics/detail-page/callout-bg.png) repeat-x; border-left: 1px solid #999999; border-right: 1px solid #999999; padding-left: 20px; padding-right: 20px; padding-bottom: 10px; width: 250px; font-family: verdana; font-size: 12px; } Two-piece transmitter/receiver design. View larger. Includes all the accessories needed. View larger. Shows the direction of the short. View larger. How Does it Work Designed for convenient, fast circuit tracing, Power Probe's ECT2000 makes use of a modern two-part transmitter/receiver design. After connecting the Smart transmitter's 20-ft power lead to the vehicle's battery, a signal is generated through the green signal wire and banana plug. This signal is connected to the circuit you want to trace and radiates along its length, which you can trace by using the Smart receiver. The Smart transmitter can generate both grounded circuit signals and open circuit signals, which because of their different characteristics depending on the conditions of the circuit tested, offer users the flexibility they need to get the job done. The Power Probe ECT2000's receiver also features the ability to lock on to either of these signal types, causing it to ignore any others, streamlining your tracing process even further. Also included with the ECT2000 are four of the most common adapters used, which helps you get connected to any electrical circuit on the vehicle. This lets you know immediately whether a circuit is shorted or open. You can also wiggle, twist, pull, push and flex wires or connectors, to observe a change in intermittent circuit conditions. The reception sensitivity feature allows you to lock in your preferred distance from the circuit. The receiver also shows the direction to the short circuit, eliminating the guesswork and having you working with circuitry like a pro. Features: Two-piece transmitter/receiver design for detecting short circuits and open circuits. Ability to lock the receiver's sensitivity for short/grounded circuits, or open circuits during tests. Includes the receiver ability to discern the direction along the circuit where the short is. Seven-level "Pulse Mode" functionality that indicates the location of a short circuit with both a increasing LED flashes and audible beeps. 4 of the most common adapters including: light bulb adapters, an alligator clip adapter and a universal wire adapter. Circuit breaker protected. Cable, and additional 20-ft extension allowing for 40-feet of total coverage. Blow molded hard case for protection. What's in the Box 1-Smart transmitter and 1-smart receiver unit, 2-AAA batteries, 1-battery Hookup ClipSet, 3-bulb adapters, 1-universal wire w/Jack, 1-blade probe, 1-back probe, 1-piercing probe, 1-alligator clip set, 1-instruction manual/DVD and rugged hard case. About Power Probe, Inc. Headquartered in Brea, CA, Power Probe, Inc. has been a trusted manufacturer of motor vehicle supplies and tools for automotive technicians since 1994. Warranty Power Probe products undergo a strict quality control inspection for workmanship, function, and safety before leaving the factory. All Power Probe products carry a one-year limited warranty from the date of purchase, applicable to the original owner, to be free of defects in parts and workmanship.

Pin-points short circuits fast! Efficient for tracing and pin pointing short circuits in 12-24 volt automotive electrical systems. You can find intermittent circuit problems by flexing wires or connectors and listening for a change in the transmitter tone. The reception distance can be locked and unlocked allowing you general tracing or pinpointing the problem location. It also shows you the direction to the short with its direction indicator, eliminating the guesswork. Cut through the chase with this proven time saving tester. It consists of 2 units, a "SMART" transmitter and a "SMART" receiver along with 4 of the most common adapters to get you connected to any electrical circuit on the vehicle. Comes with a complete instruction manual and 15-minute video.

The Haynes Automotive Electrical Manual provides you with everything you need to get up to speed on basic automotive electricity. Includes information on how to read wiring diagrams, how to use test equipment, troubleshooting, starting systems, charging systems, alternator and starter overhaul, lighting systems, auxiliary lights, gauges and indicator lights, accessories, and trailer wiring.

Haynes Techbook Motorcycle Electrical Manual This manual uses easy-to-follow text and line drawings to explain subjects from basic electrical principles to state-of-the-art systems. Over 600 illustrations! Haynes Techbooks are system specific rather than model specific. They cover theoretical and practical aspects of a system and can do so in greater detail than normally featured within a repair manual. This series of comprehensive manuals gives the home mechanic an in-depth look at specific areas of motorcycle repair. Each manual offers east-to-follow text plus hundreds of hands-on photographs.

LED Cordless Work Light Type: Cordless Work-Light & Charger Lamp Included: Yes Type of Lamp: LED Cord Length: Cordless